{"id":3146,"date":"2024-03-25T16:00:21","date_gmt":"2024-03-25T16:00:21","guid":{"rendered":"https:\/\/ohme-ev.com\/?post_type=guides&p=19473"},"modified":"2024-09-26T08:15:04","modified_gmt":"2024-09-26T08:15:04","slug":"how-do-i-install-an-ohme-epod","status":"publish","type":"guides","link":"https:\/\/ohme-ev.com\/au\/support\/how-do-i-install-an-ohme-epod\/","title":{"rendered":"How do I install an Ohme ePod?"},"content":{"rendered":"\n
\n

The installation must be compliant with any national and\/or local Regulations primarily AS\/NZS 3000 Electrical installations (known as the Australian\/New Zealand Wiring Rules). Installation should be carried out by a competent electrician with appropriate knowledge of EV charge point installations.<\/p>\n\n\n

\n\n\n
\n
\n \"\"\/\n <\/div>\n\n
\n

Step 1<\/h3>\n

<\/h4>\n

Using the drill template provided in the box, drill holes using a 7mm drill bit. Remove the front cover of the Ohme ePod and mount the back piece onto the wall using the screws provided.<\/p>\n<\/div>\n

\n <\/div>\n <\/div>\n<\/div>\n<\/div>\n\n
\n\n\n
\n
\n \"\"\/\n <\/div>\n\n
\n

Step 2<\/h3>\n

<\/h4>\n

You can feed the input cable either through the gland in the back or underside of the Ohme ePod. Once you\u2019ve done so, connect the Live, Neutral, and Earth wires.<\/p>\n<\/div>\n

\n <\/div>\n <\/div>\n<\/div>\n<\/div>\n\n
\n\n\n
\n
\n \"\"\/\n <\/div>\n\n
\n

Step 3<\/h3>\n

<\/h4>\n

The Ohme ePod has a dynamic load balancing feature. A current sensor (CT) clamp is provided to measure the electrical demand of the property, or sub-board. The unit will limit the maximum current available to the vehicle to keep the household demand below the set threshold or fuse value. Secure the wires of the data cables in the spring loaded Wago located on the front of the unit.<\/p>\n

If you\u2019re using a separate data cable and have already used the underside hole for the main cable, use the back hole to feed the cable into the unit.<\/p>\n

Note: you\u2019ll require a second gland (M12 or M16) to maintain a weatherproof seal.<\/strong><\/p>\n<\/div>\n

\n <\/div>\n <\/div>\n<\/div>\n<\/div>\n\n
\n\n\n
\n
\n \"\"\/\n <\/div>\n\n
\n

Step 4<\/h3>\n

<\/h4>\n

Reattach the front cover and install the screw caps provided with the Ohme ePod.<\/p>\n<\/div>\n

\n <\/div>\n <\/div>\n<\/div>\n<\/div>\n\n\n

Installation complete<\/strong><\/h2>\n\n\n\n

Now that you’ve successfully installed the Ohme ePod, check out the following article for how to commission an Ohme charger<\/a>.<\/p>\n\n\n\n

<\/p>\n<\/div><\/div>\n\r\n\t\t\t

\r\n\r\n\t\t\t\t
\r\n\t\t\t\t\t
\r\n\t\t\t\t\t\t

Was this helpful?<\/h3>\r\n\t\t\t\t\t<\/div>\r\n\t\t\t\t\t
\r\n\t\t\t\t\t\t
\r\n\t\t\t\t\t\t\t\r\n\t\t\t
\r\n\t\t\t\t\r\n \r\n \r\n
\r\n\t\t\t\t\r\n \r\n \r\n
\r\n\t\t\t\t\t
\r\n\t\t\t\t\t\t